Sport Kote^®
Water-Based Urethane Wood Finish (222SF)

Features | Properties | General Directions

Application Hints | Pad Recommendation

Packaging Specifications | MSDS

Features

• Single-component formula means no pot life and no mess. Finish is useable the next day if more coats are desired.
• Contains reactive polymers that offer durability and appearance equal or greater than oil-modified products.
• Excellent black mark, scuff and soil resistance.
• One hour dry time between coats under normal conditions.
• Only 24 hour gym down time.
• Uniquely restorable with high speed buffer.
• Suitable for oak, maple and parquet floors.
• MFMA approved - meets all standards set for group five products, water-based finish.
  

Properties*

• Type - Urethane/Acrylic Blend
• Form - Opaque Liquid
• Odor - Bland
• Color - Light Yellow
• Weight per Gallon - 8.60 Lbs.
• pH - 7.5-8.5
• Floor Solids - 29%
• Coverage - Up To 1000 Sq. Ft. Per Gallon (25 m2 Per Liter)
• Slip-Resistance - UL Classified
• VOC Content - 250 gm/L
  

* Properties are typical and subject to usual manufacturing tolerances.

General Directions**

1. Prepare Floor: Note: This finish is not designed for application to bare wood floors. Use only on previously sealed surfaces.
   Scrub and recoat: Dust mop floor and remove all chewing gum and labels. Clean floor with a 8 ounce per gallon dilution of Citrus Scrub 'N Shine (#525). Screen with a 120 grit screen or brown or black pad to sufficiently roughen floor. Rinse the floor with Nu-Tral Cleaner (#507) until all residue has been removed.
   Note: Test previously coated floor in an inconspicuous area before recoating to determine compatibility with existing finish. Apply 2 or 3 coats of finish. See finish application instructions below.
   
2. Apply Finish: Stir gently before using. Apply at a rate of 800-1000 square feet per gallon. Use a clean, synthetic applicator. Apply thin, even coats with the grain of the wood. Allow a dry time of at least 1 hour between coats. Humid conditions will necessitate longer dry time. After the first coat has dried, apply a second coat. It may be necessary to screen the first coat if grain raising has occurred or it has dried longer than 4 hours. If so, screen the floor with a previously used 120 grit screen or brown or black pad. Always vacuum and tack thoroughly after screening.
   Note: Do not pour unused finish back into original container. For best results, use product within 1 year of purchase date.
   
3. Maintain Daily: Dust mop at least daily, or more as required, to keep floor dust and dirt free. Damp mop spills, salt residue, etc. with Nu-Tral Cleaner and a thoroughly wrung mop.
   
4. Maintain Weekly: If soil conditions are heavy, auto-scrub weekly with red pads and a 2 ounce per gallon dilution of Nu-Tral Cleaner. Refer to the Wood Floor Care Wall Chart or Manual for further details.
   
5. Restoration: Dust mop floor. Auto-scrub with red pads with an 8 ounce per gallon dilution of Citrus Scrub 'N Shine. Then dry burnish with recommended pad.

** See label directions and MSDS for complete usage and safety instructions.

Application Hints

1. Sport Kote should be gently mixed before application.
2. During application, make sure air handlers are OFF and doors are closed to eliminate flash drying. After the application is complete and the finish has skinned over, ventilation can be turned back on.
3. Sport Kote can be applied over most existing finishes including oil-modified products. If uncertain, test in a small, inconspicuous area for compatibility first.
4. Under high humidity, dry times for Sport Kote will vary greatly. Do not apply a second coat if the first coat is still tacky.
5. Two coats is usually sufficient on recoats. If a third coat is desired, make sure the previous coats are thoroughly dry before applying product.

Burnishing Pad Recommendations *

* These are generalized classifications based on market research. Terms and definitions may be different from manufacturer to manufacturer; however, the above information will help to determine pad compatibility with various floor machines and Essential finishes on the market.

NOTE: These are polishing pad recommendations. They are not suitable for deep cleaning a wood floor prior to recoating. See product label for complete details.

Packaging Specifications

Package	Sizes Available	UPC Codes	Pack Size (inches)	Cube (ft.)	Pack Wt. (Lbs.)	Full Pallet
	5 Gallon Pail	783366222056	12 x 14	1.17	46.08	36
	2 x 2½ Plastic Container	783366222032	14 x 9.5 x 15.25	1.17	45.86	36
	4 x One Gallon	783366222049	13 x 13.5 x 12.5	1.27	36.44	36