Eccothane™
All Purpose Urethane Finish (274FF)

Features | Properties | General Directions

Application Hints | Pad Recommendations | FAQ

Packaging Specifications | MSDS

Features

• Improved formula for even smoother application.
• Multi-surface, all-purpose urethane-fortified finish for all maintenance systems.
• Long-lasting, all maintenance, all surface floor finish.
• Urethane-fortified for maximum durability and beauty.
• Combination seal and finish.
• For no buff, spray buff and ultra high speed burnish systems.
• Use on vinyl tile, linoleum, terrazzo, rubber and quarry tile floors.

Properties*

• Type - Urethane/Acrylic Emulsion
• Form - Opaque Liquid
• Odor - Bland
• Color - Milky White
• Weight Per Gallon - 8.54 Lbs.
• pH - 8.2 - 8.6
• Floor Solids - 18%
• Coverage - Up to 3,000 Sq. Ft. Per Gallon (75 m² per liter)
• Dry Time - 30 Minutes
• Slip-Resistance - UL Classified
• V.O.C. Content - < 295 gm/l

* Properties are typical and subject to usual manufacturing tolerances.

General Directions**

Application:

1. Strip floors to remove old waxes, sealers and finishes.
2. Rinse thoroughly and let dry.
3. With a clean rayon mop apply thin, even coats of Eccothane.
4. Under normal conditions, allow to dry for 30 minutes between coats.
5. For best results, apply a maximum of 4 coats in 24 hours.

Maintenance:
Daily:

1. Sweep or dust mop frequently to remove gritty soil.
2. Use our Nu-Tral Cleaner (#507) to damp mop spills as they occur. Damp mop or auto-scrub nightly with Nu-Tral Cleaner.
3. Buff if desired with high speed equipment and soft ultra high speed pads.

Weekly:

1. To repair and deep clean floor, apply Citrus Scrub 'N Shine (#525) with mop or auto-scrubber.
2. Allow floor to dry.
3. Burnish floor with high speed equipment. This finish also responds to spray buffing with conventional speed equipment. Note: Always dust mop after burnishing or spray buffing.

Periodic Recoating:

1. Dust mop entire floor then scrub aggressively using Citrus Scrub 'N Shine and auto-scrubber with a red or green pad.
2. Use a blue pad for heavily marked or unusually dirty floor.
3. Rinse floor and allow to dry.
4. Apply one or two coats of Eccothane.

** See label directions and MSDS for complete usage and safety instructions.

Application Hints

1. Eccothane can be applied to almost any substrate including rubber, marble, synthetic gym floors, linoleum and unglazed ceramic. It also works on all traditional surfaces such as VCT and terrazzo.
2. Eccothane is very easy to apply with a standard finish mop and dries perfectly clear.
3. For best results in high traffic locations (such as supermarkets) and entranceways, apply four coats the first night, then follow-up a few days later with four more coats. This gives you the desired film thickness from which to properly maintain your floor.
4. Eccothane cures slower than many finishes. A soft polishing pad (white or similar) is usually recommended for burnishing the first few days after application.

Pad Recommendations *

Packaging Specifications

Package	Sizes Available	UPC Codes	Pack Size (inches)	Cube (ft.)	Pack Wt. (Lbs.)	Full Pallet
	55 Gallon Drum	783366274000	23 x 34	10.41	490.58	4
	5 Gallon Pail	783366274055	12 x 14	1.17	45.78	36
	4 x One Gallon	783366274048	13 x 13.5 x 12.5	1.27	36.2	36